+86 0519 8878 2189
News Center
Home / News / All-Aluminum Heating & Evaporator Coils for HVAC | CST

All-Aluminum Heating & Evaporator Coils for HVAC | CST

Views: 0     Author: Site Editor     Publish Time: 2026-11-12      Origin: Site

At CSTHEATEXCHANGER, we design and manufacture high-performance All-Aluminum Heating Coils, Evaporator Coils, and Reversible Heat Pump Heat Exchangers specifically engineered for commercial air handling units (AHU), rooftop packaged units (RTU), ductless & VRF split systems, residential heat pumps, and commercial hydronic ventilation systems (thermal capacities scaled from 3 kW to over 650 kW, operating design pressures up to 4.5 MPa / 45 bar for R410A, R32, R454B, R290 propane, and hot water / glycol hydronic heating). Fabricated from monolithic high-purity aluminum alloys (AA3003 / AA3102 / AA4045) utilizing continuous Controlled Atmosphere Brazing (CAB) or all-aluminum round-tube construction, CST all-aluminum coils cut equipment weight by up to 60%, reduce internal refrigerant volume by 70%, completely eliminate galvanic bimetallic corrosion, lower air static pressure drop by 20%–25%, and provide significant manufacturing raw material cost savings over volatile copper tube-fin alternatives.

CSTHEATEXCHANGER All-Aluminum Heating & Evaporator Coils for HVAC Systems.jpg

1. Thermodynamic & Structural Engineering: Monolithic Aluminum in Modern HVAC

Transitioning from traditional copper-tube aluminum-fin (Cu/Al) coils to all-aluminum heat exchangers solves the most critical failure mode in HVAC systems—bimetallic galvanic corrosion:

        HVAC COIL METALLURGICAL EVOLUTION: Cu/Al VS. ALL-ALUMINUM MCHE
        
   [A. TRADITIONAL COPPER TUBE / ALUMINUM FIN HVAC COIL]
     CONDENSATE MOISTURE ──► [ COPPER-ALUMINUM GALVANIC CELL (0.75V Potential Gap) ]
     (High Humidity)           • Aluminum fin collars corrode and flake away (White rust)
                               • Micro-gaps form (Loss of mechanical contact thermal conduction)
                               • Heavy structural weight forces thicker casing steel
     
   [B. CST 100% MONOLITHIC ALL-ALUMINUM HEATER & EVAPORATOR COIL]
     CONDENSATE MOISTURE ──► [ UNIFORM PASSIVE OXIDE LAYER (0.00V Galvanic Potential) ]
     (High Humidity)           • Single-alloy CAB nitrogen metallurgical bonding
                               • Zinc-diffused sacrificial layers prevent moisture pitting
                               • 60% lighter weight & streamlined low-drag aerodynamic profile
================================================================================
CST ALL-ALUMINUM HVAC COILS VS. TRADITIONAL COPPER TUBE-ALUMINUM FIN COILS
================================================================================
Evaluation Metric              CST All-Aluminum HVAC Coil       Traditional Copper Tube / Aluminum Fin
--------------------------------------------------------------------------------
Equipment Weight & Load        55% to 65% Lighter (Pure aluminum)Extremely Heavy (Heavy copper pipe mass)
Thermal Contact Degradation    0% Loss (100% Metallurgical CAB Braze)2%–8% Loss over time (Mechanical expansion)
Galvanic Corrosion Risk        Eliminated (100% Monolithic Al Alloy)High Risk (Cu-Al galvanic cell in moisture)
Internal Fluid / Refrigerant VolUp to 70% Volume Reduction       Large Internal Holding Volume
Air-Side Form Drag (Pressure)  20% to 25% Lower Static ResistanceHigh Drag (Round-tube wake dead zones)
Raw Material (BOM) Cost Impact 25% to 40% Cost Savings vs. CopperHigh & volatile copper pricing baseline
Recyclability & Eco Lifecycle  100% Single-Alloy Scrap Value     Complex & costly Cu-Al scrap separation
Operating Pressure Capability  Up to 4.5 MPa (45 bar / 652 psi) 2.5 to 3.0 MPa Standard Design Limit
================================================================================

1. Complete Elimination of Galvanic Bimetallic Corrosion

In humid cooling and heating cycles, condensed moisture bridges copper tubes and aluminum fins, creating a galvanic cell that degrades the aluminum fin collar. CST all-aluminum coils are 100% fabricated from matched metallurgical aluminum alloys, eliminating galvanic potential differences and ensuring zero fin bond degradation over decades of service.

2. High-Efficiency Multi-Port Flat Tube Aerodynamics

Unlike round copper tubes that create turbulent wake dead zones on the leeward side of each tube, our extruded multi-port flat microchannel tubes offer streamlined aerodynamic airflow. This maximizes air contact with louvred fins while reducing air static pressure drop by up to 25%, allowing HVAC equipment manufacturers to use smaller, quieter fan motors.

2. Metallurgy & Manufacturing Engineering: Continuous Controlled Atmosphere Brazing (CAB)

CSTHEATEXCHANGER manufactures all-aluminum coils under strict cleanroom and continuous nitrogen atmosphere brazing standards:

        CST ALL-ALUMINUM HVAC COIL METALLURGY
        
   ┌─────────────────────────────────────────────────────────────────────────┐
   │ [1. MULTI-PORT EXTRUDED FLAT TUBES / ALUMINUM ROUND TUBES]              │
   │ • High-purity AA3003 / AA3102 alloy with high burst strength (>15 MPa). │
   │ • Internal micro-channels optimize refrigerant evaporation & water flow.│
   ├─────────────────────────────────────────────────────────────────────────┤
   │ [2. HIGH-DENSITY HYDROPHILIC & LOUVRED FINS]                            │
   │ • Clad with AA4045/AA4343 braze alloy with zinc (Zn) anti-pitting layer.│
   │ • Hydrophilic surface coating ensures rapid condensate drainage.        │
   ├─────────────────────────────────────────────────────────────────────────┤
   │ [3. D-SHAPED EXTRUDED ALUMINUM HEADERS & TRANSITIONS]                   │
   │ • Laser-cut internal baffles for uniform multi-pass refrigerant circuit.│
   │ • Factory friction-welded copper stubs for standard field brazing.      │
   └─────────────────────────────────────────────────────────────────────────┘
       CST ALL-ALUMINUM HVAC COIL CAB PRODUCTION WORKFLOW
       
   FROM HIGH-SPEED FIN STAMPING & TUBE SLOTTING
   ┌─────────────────────────────────────────────────────────────────────────┐
   │ [ STAGE 1: AUTOMATED MATRIX STACKING & FLUX APPLICATION ]               │
   │ Precision robotic assembly with non-corrosive NOCOLOK spray flux        │
   ├─────────────────────────────────────────────────────────────────────────┤
   │ [ STAGE 2: CONTINUOUS TUNNEL CAB NITROGEN FURNACE BRAZING ]             │
   │ +600°C thermal curve forms 100% void-free metallurgical contact nodes   │
   ├─────────────────────────────────────────────────────────────────────────┤
   │ [ STAGE 3: 100% HIGH-PRESSURE PROOF & HELIUM VACUUM LEAK TEST ]         │
   │ Tested at 6.5 MPa (65 bar); Helium leak rate < 1x10⁻⁶ mbar·L/s          │
   ├─────────────────────────────────────────────────────────────────────────┤
   │ [ STAGE 4: HYDROPHILIC / E-COAT COATING & COPPER TRANSITION STUBS ]     │
   │ Ensures rapid water drainage and standard copper torch field piping     │
   └─────────────────────────────────────────────────────────────────────────┘
   DELIVERS MAXIMUM HVAC RELIABILITY & ZERO LEAK OPERATION

1. 100% Solid Metallurgical Bond (Zero Thermal Contact Loss)

Mechanical tube expansion used in traditional copper coils gradually loosens under seasonal thermal expansion and contraction cycles. CST's CAB nitrogen brazing creates a solid metallurgical bond across 100% of the fin-to-tube contact area, permanently eliminating contact thermal resistance.

2. Hydrophilic Fin Coating for Rapid Condensate Drainage

In evaporator mode, water droplets bridging narrow fin gaps can choke airflow and cause water carryover into supply ducts. CST applies advanced hydrophilic coatings to all evaporator fins, reducing water surface contact angles so condensate forms a thin film that drains rapidly into the drain pan.

3. Product Configurations: HVAC Heating & Evaporator Topologies

        CSTHEATEXCHANGER ALL-ALUMINUM HVAC COIL PORTFOLIO
        
   [1. DIRECT EXPANSION (DX) EVAPORATOR COILS]
   • Scaled for residential and commercial split AC, heat pumps, and RTUs (3 kW to 150 kW).
   • Compatible with high-pressure eco refrigerants: R410A, R32, R454B, and R290.
   ─────────────────────────────────────────────────────────────────────────────
   [2. HYDRONIC HEATING & COOLING WATER COILS]
   • Engineered for air handling units (AHU), fan coil units (FCU), and duct heaters (Hot/Chilled water).
   • Multi-pass header baffles maintain optimal water velocity with minimal fluid pressure drop.
   ─────────────────────────────────────────────────────────────────────────────
   [3. REVERSIBLE HEAT PUMP OUTDOOR & INDOOR COILS]
   • Specially circuited for dual-mode operation (summer cooling evaporator + winter heating condenser).

4. Technical Specifications — All-Aluminum Heating & Evaporator Coils

(Note: The following engineering parameters represent standard manufacturing design envelopes. Core dimensions, fin density, tube port geometry, header configurations, and mounting flanges are 100% custom-tailored to specific HVAC chassis blueprints and thermal capacities.)

================================================================================
CST ALL-ALUMINUM HVAC COIL (CST-AL-HVAC SERIES)
================================================================================
Engineering Parameter           Standard Manufacturing & Design Range
--------------------------------------------------------------------------------
Thermal Capacity Range          3 kW to 650+ kW per coil block (Custom Modular Sizing)
Operating Function Modes        Direct Expansion (DX) Evaporator, Condenser, Hydronic Water Heater
Fluid Media Compatibility       R410A, R32, R454B, R134a, R290 (Propane), Hot Water, Chilled Glycol
Design Operating Pressure Range Up to 4.5 MPa (45 bar / 652 psi) High-Pressure Certified
Hydrostatic Proof Test Pressure 6.5 MPa (65 bar / 942 psi) Leak Integrity Quality Gate
Base Metallurgy Structure       100% Monolithic Aluminum (AA3003, AA3102, AA4045, AA6063)
Core Depth / Thickness Profile  16 mm, 20 mm, 25 mm, 32 mm, 40 mm, 50 mm Ultra-Slim Profile
Extruded Flat Tube Width (Depth)12 mm to 42 mm Multi-Port Tubes (8 to 24 micro-channels/tube)
Fin Density / Geometry          14 to 26 FPI (Multi-Louvred Corrugated Hydrophilic Aluminum)
Surface Treatment Options       Hydrophilic Blue Coating, Zinc Diffusion, Cathodic E-Coat, Blygold
Fluid Connection Ports          Factory Friction-Welded Copper Stubs, Aluminum Stubs, Flanges
Weight Advantage Ratio          55% to 65% Lighter than equivalent capacity copper tube-fin coil
Air-Side Static Pressure Drop   20% to 25% Lower Air Resistance than equivalent copper coil
Refrigerant Charge Savings      Up to 70% Less Internal Volume vs. Round Tube Coils
Quality Standards & Compliance  CE / PED 2014/68/EU, ISO 9001:2015, UL 207, RoHS Compliant
Testing & Quality Assurance     100% Helium Mass Spectrometer Vacuum Leak Testing
================================================================================

5. Frequently Asked Questions (FAQ)

Can an all-aluminum coil be used as both an evaporator and a heater in heat pumps?

Yes. CST designs reversible all-aluminum microchannel coils specifically engineered for heat pumps. The internal header baffles and circuiting are optimized to handle two-phase evaporating refrigerant during summer cooling and high-pressure condensing vapor during winter heating, delivering high seasonal coefficient of performance (SCOP).

How do field technicians connect all-aluminum coils to standard copper refrigerant lines?

CST equips all replacement and OEM microchannel coils with factory friction-welded (or explosion-bonded) copper transition stubs. This allows field installers and manufacturing assembly lines to braze standard copper suction, liquid, and hot gas lines using ordinary copper brazing rods and standard torches—no specialized aluminum brazing training required.

How does the hydrophilic coating prevent water droplet carryover in evaporator coils?

In untreated aluminum or copper coils, condensed water forms spherical beads that bridge the fin gaps, choking airflow and getting blown into the air duct. CST's hydrophilic coating reduces water droplet surface tension, causing moisture to spread into a continuous ultra-thin water film that drains immediately into the condensate pan, maintaining unrestricted airflow.

Source Custom All-Aluminum HVAC Coils from CSTHEATEXCHANGER

Cut HVAC manufacturing costs, reduce equipment weight, and eliminate galvanic corrosion with CSTHEATEXCHANGER:

  • Custom All-Aluminum Heating & Evaporator Coils

  • 25% to 40% Lower BOM Raw Material Cost Compared to Copper Tube-Fin Coils

  • 55% to 65% Weight Reduction with Up to 70% Less Refrigerant Charge Required

  • 100% Monolithic Aluminum Construction Eliminating Bimetallic Galvanic Corrosion

  • Factory Friction-Welded Copper Transition Stubs for Standard Field Copper Brazing

  • Full CE / PED & UL 207 Compliance, 100% Helium Mass Spectrometer Tested & Fast Global Delivery

Contact our specialized HVAC/R thermal engineering team today with your coil dimensions (length ×× height ×× depth), airflow CFM/m3/h, fluid or refrigerant type, and target heating/cooling capacity for custom thermal modeling proposals and factory-direct quotations.

PHONE

International Business:+86 0519 8878 2189

Domestic business:+86 0519 8878 2190

QUICK LINKS

PRODUCTS

ABOUT US

When it comes to building heat exchanger for any application VRCOOLERTECH has the capability to meet your requirements.
Copyright © 2021 Changzhou Vrcoolertech Refrigeration Co.,Ltd All rights reserved.  Sitemap  Manage Entrance